• A SNMP agent for ComAp NT line controllers
• Connected to the controllers via RS485 (Modbus)
• Up to 32 controllers served by one device
• Provides access to basic operational and statistic values (not configurable) using GET transaction
• Generates a TRAP event if any protection occurs in the controller
• Mode change and basic genset control is also available via SET transaction

• 8 analog outputs extension module
• Applicable to: InteliSys, InteliDrive, IGS-NT
• Up to four I-AOUT8 can be connected to one controller
• Outputs are configurable to: 
• 0-10VDC or
• 0/4-20mA range or
• 1200 Hz pwm
• UL certified

• Versatile programmable interface unit between Inteli NT, InteliSys or InteliDrive controller and CCM
• For diesel engines
• UART interface
• Selected analog and binary values are received from CCM via I-CB
• UL certified

• Versatile programmable interface unit between Inteli NT, InteliSys or InteliDrive controller and CCM
• For gas engines
• UART interface
• Selected analog and binary values are received from CCM via I-CB
• UL certified

• Programmable interface unit between Inteli NT, InteliSys or InteliDrive controller and Deutz TEM Evolution unit
• Configured analog and binary values, alarms and faults are received from Deutz TEM Evolution unit via I-CB and displayed on IS measurement screens
• UART interface
• UL certified

• Versatile programmable interface unit between Inteli NT, InteliSys or InteliDrive controller and the Engine Control Unit
• CAN bus interface
• Selected analog and binary values are received from ECU via i-CB
• UL certified

Used for CAN bus extension in cases where the maximum distance limit would be exceeded.

• Intercontroller CAN bus extension (one or more I-CR modules can be used)
• Intercontroller CAN bus bus-tie bridging - makes groups of controllers in segments A and B "invisible" one for another depending on bus-tie breaker state, keeping the PC communication (IG-MU, IG-IB) in function for all controllers
• Peripheral CAN bus extension

• Interface between IG-PCM/PCLSM, InteliSys or Inteli NT cotroller and generator AVR

• Acknowledged by Germanischer Lloyd
• Connects IG-PCM/PCLSM with generator AVR

• Primary voltage: 100 - 120 VAC +- 20%
• Frequency range: 50 - 60 Hz
• Designed for HV or MV applications

• Primary voltage 1: 230 - 277 VAC +- 20%
• Primary voltage 2: 400 - 480 VAC +- 20%
• Frequency range: 50 - 60 - 400 Hz

• Primary voltage 1: 230 - 277 VAC +- 20%
• Primary voltage 2: 400 - 480 VAC +- 20%
• Frequency range: 50 - 60 - 400 Hz

• Enables communication among InteliGen/InteliMains controllers via CAN bus
• Enables Power management feature of InteliGen controllers
• Attached at the back of InteliGen/InteliMains controller

• Acknowledged by Germanischer Lloyd
• Enables communication among InteliGen/InteliMains controllers via CAN bus
• Enables Power management feature of InteliGen controllers
• Attached at the back of InteliGen/InteliMains controller

• Using Internet Bridge you can easily service and monitor your gen-set even from the other side of earth
• Enables internet connection between controllers (IGS-NT, InteliGen, InteliSys, InteliDrive) and superior service or monitoring software (GenConfig, InteliMonitor, InteliSupervisor, IGS-LOG, WinEdit, MultiEdit, DriveConfig or DriveMonitor)
• Ethernet or dial-up connection of the controller to the internet
• Supports single/multiple gen-set control via Internet
• Sends active e-mails in case of alarm on site
• For more gen-sets additional hardware key (IG-IB3, IG-IB7, IG-IB15, IG-IB32) is required
• UL certified

• Input and output extension module
• 8 binary and 4 analog inputs
• 8 binary and 1 analog output
• Connection via CAN bus
• Not galvanic separated

IG/IS-NT MultiKit

• Small switchboard for testing multiple gen-set applications
• Contains three InteliGen NT /    InteliSys NT, 1 InteliMains NT, Engine and Mains simulators
• Controllers are connected with load sharing line and CAN bus
• Shared connection to all controllers via built-in I-LB (for PC monitoring)

On-line controller - you can test the IG/IS-NT controller functionality and setting on-line; all you need to do is to download and install IG/IS-NT Installation package and manuals.

How to connect to the controller:

• Start InteliMonitor, click on Open connection icon, select Connect to selected site, select IS-internet site and click on Open connection.
• It is necessary to unlock controller if you want to edit setpoints. Click on the lock icon or press Ctrl+P to open Login window. Select User as the user name and write 0 as the password. 
• It may happen that somebody else is already connected to the on-line controller (up to 4 users can be connected to the controller at the same time) and signed up for controller setpoints editing. Attempt to login may be followed by error message: Invalid password/New controller 1. Please, try to login later if this message is displayed.
  

This controller is available via analog modem, too. Phone number you have to dial is +420 284 825 909.

Please note, that available on-line controller is the IS-NT StarterKit controller. It means:

• Mains current simulation is not available in the IS-NT StarterKit, therefore power Export/Import simulation is not possible.
• Features and setpoints of the IS-NT controller which are not available in the IG-NT controller are marked in manual with cyan background. 
  
  Do not hesitate to contact us if you have any questions regarding controller setting or functions.

• Extension signalling unit for InteliLite, InteliGen, or InteliSys gen-set controllers
• 15 LEDs with configurable colors red-green-yellow
• Customizable labels
• Local horn output
• Lamp test function
• Connected via CAN bus, max distance 200m from the controller
• UL certified

• Set of 3 mains voltage transformers 400V/230V
• Galvanic separation of the mains and generator voltage
• For three wire system, system with separated Neutral or when galvanic separation between generator or mains voltage and controller is required

• Set of three mains voltage step down transformers 600V/300V (transformer ratio 2:1) 
• For applications where mains/bus/generator voltage is higher than controller measuring range
• Galvanic separation of the mains and generator voltage
• For three wire system, system with separated Neutral or when galvanic separation between generator or mains voltage and controller is required

• For marine applications
• Set of 3 mains voltage transformers 400V/230V
• Galvanic separation of the bus and generator voltage

• Set of 3 mains voltage transformers 400V/230V
• For three wire system, system with separated Neutral or when galvanic separation between generator or mains voltage and controller is required
• Additional filter for the cases of extreme distortion of generator voltage by higher harmonics due to inverters etc.

• Direct or modem control of multiple gen-sets
• RS422/RS485/ModBus support for direct connection
• Analog/GSM/ISDN modem support
• Modem callback function
• UL certified

• For isolated parallel or parallel to mains operation
• Analog isochronous load sharing line
• Automatic forward and reverse synchronizing
• Speed/voltage control
• Load control including ramping
• Power factor, import/export control
• Additional 4 binary inputs and outputs

• Acknowledged by Germanischer Lloyd
• For isolated parallel operation
• Analog isochronous load sharing line
• Automatic forward and reverse synchronizing
• Speed/voltage control
• Soad control including ramping
• Sower factor, import/export control
• Additional 4 binary inputs and outputs

• For parallel to mains operation
• Automatic forward and reverse synchronizing
• Speed/voltage control
• Load control including ramping
• Power factor, import/export control
• Additional 4 binary inputs and outputs

Enables multiple isolated parallel or multiple parallel with mains operation (with CAN bus)

• Digital Load Sharing
• Digital VAr Sharing
• Optimizing number of running engines: Power management; kW, kVA or % load based

Enables to increase the number of PLC functions used with IG-NT/EE controllers to allow the design of a simple CHP unit. Special set of archives should be used with this module: IG-apl_name-mCHP-version.

Actual number of available PLC functions can be found in Application guide for NT controllers.

• Input and output extension module
• 8 binary and 4 analog inputs
• 8 binary and 1 analog output
• Measures values from Pt100 and Ni100 sensors
• Analog inputs have maximum resistance range 0-250 Ohms, voltage range 0-100mV, current range 0-20mA - selectable via jumper
• UL certified

• Bridge for sites with multiple controllers for local or remote monitoring and control
• Direct, modem or USB (I-LB+ version only) connection to multiple controllers
• RS232 / RS485 / ModBus support for direct connection
• Communication speed up to 57600 bps (including ModBus mode)
• Analog / GSM / ISDN / CDMA modem support

Module connected between 12 V DC battery and controller power terminals to support controller operation during battery voltage dips.

• Suitable for InteliGen/Inteli NT/InteliLite controllers
• Keeps the controller operating during battery voltage drop, e.g. while the engine is cranking

• Gauge driver plug-in interface
• Applicable to InteliLite NT (IL-NT)
• Up to 8 gauges (VDO, Datcon,...) can be driven by one controller

• Extension board containing RS232 port for InteliLite NT (IL-NT) controllers

InteliGen NT StarterKit

• Includes one InteliGen NT controller
• All binary inputs are connected to switches
• Binary output states are indicated by LEDs
• Analogue inputs changeable by potentiometers
• Connection to PC via RS232 serial line

InteliGen® MultiKit

• Small switchboard for testing multiple gen-set applications
• Contains three InteliGens, one InteliMains, Engine and Mains simulators
• Controllers are connected with load sharing line and CAN bus

• Shared connection to all controllers via built-in IG-MU (for PC monitoring)

InteliGen® StarterKit

• Includes one InteliGen controller
• All binary inputs are connected to switches
• Binary output states are indicated by LEDs
• Analogue inputs changeable by potentiometers
• Connection to PC via RS232 serial line

InteliLite® StarterKit

• Includes one InteliLite controller
• All binary inputs are connected to switches
• Binary output states are indicated by LEDs
• Analogue inputs changeable by potentiometers
• Connection to PC via RS232 serial line

• Unit with extension modules IS-AIN8 and IS-BIN16/8
• All binary and analogue inputs can be simulated
• Outputs are indicated by LEDs
• IS-AB Kit can be connected to IS- or ID-Starter kit

InteliSys NT StarterKit

• Includes one InteliSys NT controller
• All binary inputs are connected to switches
• Binary output states are indicated by LEDs
• Analog inputs changeable by potentiometers
• Connection to PC via RS232 serial line

InteliSys® MultiKit

• Small switchboard for testing multiple gen-set applications
• Contains three InteliSys and one InteliMains controller
• Controllers connected with load sharing line and CAN bus

• Shared connection to all controllers via built-in IG-MU (for PC monitoring)

InteliSys® StarterKit

• Contains one InteliSys controller
• All binary inputs connected to alteration switches
• Binary output states indicated by LEDs
• Analog input values changeable by potentiometers
• Connection to PC via RS232 serial line

• New generation display unit for either IGS-NT or ID controllers
• 8" colour TFT display with resolution of 800 × 600 pixels
• Controlled by active buttons TRENDS monitoring screen as a standard feature
• Developed from IS-Display Windows CE operating system
• Simpler, faster and more intuitive control
• More information in less time
• Same language support as IGS-NT and ID
• Screen configuration by customer - export to XML format with subsequent manual screen modification and import back to the controller (as IS-Display)
• Direct connection to the controller (converters are not needed)
• The same dimensions as IS-Display / IS-NT (including cut out dimensions)
• It is possible to mount IS-NT-BB to the rear side of InteliVision
• Can be used as a replacement for (or an alternative to) IG-Display, IS-Display or I-RD-CAN
• Plug and Play operation (auto configuration based on controller application)
• Designed to be mounted in both monitoring and engine room
• This display gives complete access to all control and monitoring functions when connected to IGS-NT / ID controllers
• Universal solution - one type of display for both controller families - IGS-NT and ID
• Intended for connection to ONE controller (IGS-NT or ID)
• Connection to a controller via RS232/485 and CAN bus
• Operating temperature from -20 to + 70°C (-4/158°F)
• Sealed to IP65

• 8 relays in sockets
• Both n.o. and n.c. contacts available
• 24 VDC supply
• 16A resistive and 4 A inductive load at 24 VDC
• DIN rail design

• 8 relays in socket
• Both n.o. and n.c. contacts
• 24 VDC supply
• 2 Amps load at 231 VAC
• DIN rail design

• 16 relays in socket
• Both n.o. and n.c. contacts
• 24VDC supply
• 16A resistive and 4 A inductive load  at 24 VDC
• DIN rail design

• 16 relays in socket
• Both n.o. and n.c. contacts
• 24VDC supply
• 2 Amps load at 231 VAC
• DIN rail design

• Remote signalling and control unit with RS232 interface
• For InteliGen and InteliLite gen-set controllers
• Gen-set can be controlled from I-RD as well as from master controller
• I-RD screens display the same as master controller
• Buttons and LEDs have the same function
• Order code I-RD/IG-CU, I-RD/AMF25, I-RD/MRS10, etc

• 8 analogue inputs
• Connection via CAN bus
• Precision of inputs is 1%
• Accept 2/3 wire resistive, current, voltage senders
• UL certified

• 16 inputs and 8 transistor outputs
• Inputs galvanically separated
• 2 pulse inputs (frequency measurement or pulse counting)
• Connection via CAN bus
• UL certified

Powerful graphic display module for IS-NT controllers. Up to 3 displays can be connected to one Base Box module (IS-NT-BB), providing both local and remote (up to 1200 m) monitoring and control of a gen-set.

• Required for MINT application
  Enables:
• Synchronizing and load control
• Voltage and PF control
• Load and VAR sharing

Enables in MINT application:

• Synchronizing and load control
• Voltage and PF control
• Load and VAR sharing
• Power management

• Required for SPtM and SPI applications
• Enables synchronizing and load control
• Enables voltage and PF control

• Remote signalling and control unit with RS232 interface
• For InteliSys
• Gen-set can be controlled from IS-RD as well as from master controller
• IS-RD screens display the same as master controller
• Buttons and LEDs have the same function

NT-Converter is an interface module for IG/IS-NT controllers. It allows to connect them into an existing system consisting of some third-party gen-set controllers (Woodward, Barber-Colman, ...) or IG/IS classic line controllers via their analog Load Sharing lines and CAN2 bus.

NT-Converter-1.1 allows to connect one IG/IS-NT controller into a system consisting of third-party controllers with Load Sharing capability. The connection via CAN bus allows to use Var sharing and synchronized parameters.

One logical group can be created with several IG-CU or IS-CU and with IG/IS-NT. The module allows controller monitoring via IG-MU, IG-IB or I-LB/I-LB+.