• 8 analog outputs extension module
• Applicable to: InteliSys, InteliDrive, IGS-NT
• Up to four I-AOUT8 can be connected to one controller
• Outputs are configurable to: 
• 0-10VDC or
• 0/4-20mA range or
• 1200 Hz pwm
• UL certified

• Interface for CAN1 Extension and J1939 modules
• Interface for CAN2 Inter-controller and I-RD-CAN modules
• Interface for J1708 redundancy line
• UL certified

• Backup module for marine engines
• Automatic switchover between primary and secondary power supply
• Monitors function of main InteliDrive unit
• In case of main unit failure switches to the backup mode and protects the engine
• RPM input with hardwired overspeed protection
• 5 shutdown channels with Broken Wire detection
• Fuel and Stop solenoids with BW detection

Interface module for InteliDrive controllers for full support of internal PLC (programmable logic) in wide range of industrial applications.

Module is mounted directly on ID-DCU controller body. Module I/O:

• RPM1, RPM2: Inputs for frequency measuring - up to 8 kHz
• IMP1, IMP2: Inputs for integral (consumption) measuring up to 60 Hz
• AOUT1, AOUT2: Analog outputs 0 - 10VDC or 0 - 20 mA
• Speed Governor Output: ±10VDC or ±10VDC via 10kΩ or PWM (1,6kHz ) 
• UL certified

• Extension signalling unit for InteliLite, InteliGen, or InteliSys gen-set controllers
• 15 LEDs with configurable colors red-green-yellow
• Customizable labels
• Local horn output
• Lamp test function
• Connected via CAN bus, max distance 200m from the controller
• UL certified

• Input and output extension module
• 8 binary and 4 analog inputs
• 8 binary and 1 analog output
• Measures values from Pt100 and Ni100 sensors
• Analog inputs have maximum resistance range 0-250 Ohms, voltage range 0-100mV, current range 0-20mA - selectable via jumper
• UL certified

• InteliDrive Binary and Analog inputs simulation
• InteliDrive Binary outputs indication
• ID-SCM (Speed Control Module) simulation

• InteliDrive Binary and Analog inputs simulation
• InteliDrive Binary outputs indication
• ID-RPU I/O simulation and indication
• ID-DCU and ID-RPU RPM simulation

• New generation display unit for either IGS-NT or ID controllers
• 8" colour TFT display with resolution of 800 × 600 pixels
• Controlled by active buttons TRENDS monitoring screen as a standard feature
• Developed from IS-Display Windows CE operating system
• Simpler, faster and more intuitive control
• More information in less time
• Same language support as IGS-NT and ID
• Screen configuration by customer - export to XML format with subsequent manual screen modification and import back to the controller (as IS-Display)
• Direct connection to the controller (converters are not needed)
• The same dimensions as IS-Display / IS-NT (including cut out dimensions)
• It is possible to mount IS-NT-BB to the rear side of InteliVision
• Can be used as a replacement for (or an alternative to) IG-Display, IS-Display or I-RD-CAN
• Plug and Play operation (auto configuration based on controller application)
• Designed to be mounted in both monitoring and engine room
• This display gives complete access to all control and monitoring functions when connected to IGS-NT / ID controllers
• Universal solution - one type of display for both controller families - IGS-NT and ID
• Intended for connection to ONE controller (IGS-NT or ID)
• Connection to a controller via RS232/485 and CAN bus
• Operating temperature from -20 to + 70°C (-4/158°F)
• Sealed to IP65

• 8 relays in sockets
• Both n.o. and n.c. contacts available
• 24 VDC supply
• 16A resistive and 4 A inductive load at 24 VDC
• DIN rail design

• 8 relays in socket
• Both n.o. and n.c. contacts
• 24 VDC supply
• 2 Amps load at 231 VAC
• DIN rail design

• 16 relays in socket
• Both n.o. and n.c. contacts
• 24VDC supply
• 16A resistive and 4 A inductive load  at 24 VDC
• DIN rail design

• 16 relays in socket
• Both n.o. and n.c. contacts
• 24VDC supply
• 2 Amps load at 231 VAC
• DIN rail design

• Remote control panel for the ID-DCU master controller
• Applicable up to 900 meters distance from master controller
• The same front facia, LED's and button handling

• 8 analogue inputs
• Connection via CAN bus
• Precision of inputs is 1%
• Accept 2/3 wire resistive, current, voltage senders
• UL certified

• 16 inputs and 8 transistor outputs
• Inputs galvanically separated
• 2 pulse inputs (frequency measurement or pulse counting)
• Connection via CAN bus
• UL certified